Start practice — 15 questions →
Sample questions (showing 8 of 15)
Under which condition is an applicator prohibited from applying StriCore?
- When wind speeds exceed 15 mph.
- When applying to turfgrass in residential areas.
- When using surfactants that have been tested for compatibility.
- When applying to seeded or sodded turfgrass.
Show answer
Do not apply when wind speeds exceed 15 mph.🔗 Source
According to the label, which of the following is a requirement for Personal Protective Equipment (PPE) for all handlers?
- Chemical-resistant apron and boots.
- Long-sleeved shirt, long pants, shoes plus socks, protective eyewear, and waterproof gloves.
- N95 respirator, long sleeves, and chemical-resistant gloves.
- Long-sleeved shirt, long pants, chemical-resistant boots, and a face shield.
Show answer
PPE: Long-sleeved shirt and long pants, shoes plus socks, protective eyewear, and waterproof gloves are required for applicators and all other handlers.🔗 Source
Under which weather condition should an applicator avoid applying StriCore due to the risk of droplet evaporation?
- High wind speeds exceeding 15 mph
- Low relative humidity
- Temperature inversions
- Conditions favoring wind erosion of soil
Show answer
The timing and weather section states: 'Avoid application in low relative humidity to prevent droplet evaporation.'🔗 Source
What is the required procedure for mixing StriCore with water?
- Fill the tank with water, then add StriCore and agitate.
- Mix with one fourth of the volume of clean water needed for the area to be treated, starting agitation before adding StriCore.
- Mix with full volume of water and agitate until the product is dissolved.
- Dilute StriCore with surfactants to ensure even mixing.
Show answer
The mixing instructions state: 'Mix with one fourth of the volume of clean water needed for the area to be treated. Start agitation and add StriCore to the tank.'🔗 Source
According to the mixing instructions, what should be done immediately after adding StriCore to the tank and mixing thoroughly?
- Begin spraying the target area immediately.
- Add another product to the tank.
- Fill the tank to capacity and operate the sprayer for 15 minutes to flush equipment.
- Wait 12 hours before operating the sprayer.
Show answer
Fill the tank to capacity and operate the sprayer for 15 minutes to flush hoses, boom, and nozzles.🔗 Source
What is the required Personal Protective Equipment (PPE) for handling StriCore?
- Long-sleeved shirt, long pants, shoes, protective eyewear, and waterproof gloves
- Long-sleeved shirt, long pants, boots, and chemical-resistant apron
- N95 mask, gloves, eyewear, and long-sleeved shirt
- Long pants, shoes, and waterproof gloves
Show answer
The PPE section lists: 'long-sleeved shirt, long pants, shoes, protective eyewear, and waterproof gloves'.🔗 Source
According to the product description, what is the maximum annual application rate of StriCore per acre?
- 1.5 lb a/i/acre
- 4 lbs of Pethoxamid per gallon
- 48 fl oz per acre
- 15 fl oz per acre
Show answer
The label states: 'Do not apply more than 48 fl oz of StriCore per acre (1.5 lb a/i/acre) per year.'🔗 Source
When mixing StriCore, what is the correct procedure for filling the spray tank?
- Fill the tank to capacity, then add StriCore and water.
- Fill the spray tank one-fourth full with clean water, add StriCore, and then fill to capacity.
- Fill the tank one-half full with water, add StriCore, and then fill to capacity.
- Fill the tank one-quarter full with StriCore and then add water.
Show answer
Fill spray tank one-fourth full with the water of clean water needed for the area to be treated. Start the agitation system and add StriCore to the tank. Fill the tank to capacity...🔗 Source
← All practice exams